5′ × 10′ (1524mm x 3048mm) aluminum sheet
Width 5 feet (1524mm)
Length 10 feet (3048mm)
Thickness 0.2mm - 350mm
Alloy 1100, 3003, 3105, 5005, 5052, 5754, 6061, etc
Temper O - H112, T3 - T8, T351 - T851 etc.
Technology hot rolled ( DC ), cold rolling ( CC ), Casting and rolling
5′ × 10′ aluminum sheet
5′ × 10′ aluminum sheet detailed introduction
5′ × 10′ alloy aluminum sheet is a common size of aluminum sheet & plate, 5′ × 10′ Convert to international common size is 1524mm x 3048mm, Next, I will tell you about the size conversion:
5′ × 10′ = 5 feet x 10 feet
1′ = 1 feet = 0.3048m = 30.48cm = 304.8mm
5′ = 5 feet = 1.524m = 152.4cm = 1524mm
10′ = 10 feet = 3.048m = 304.8cm = 3048mm
5′ × 10′ also used called 5 by 10, 5’x10’, 5″x10″, 5x10, 10×5, 60×120, etc.
After understanding the conversion of inches, feet and international units of length, you will clearly know the specific size of each commonly used size
The commonly used dimensions of aluminum plates are:
Unit ( foot ): 4×4, 4×6, 4×8, 4×10, 4×12, 5×8, 5x10, 6×8 etc.
Unit ( inch ): 12×12, 16x16, 24×24, 24×36, 24×48, 36×36, 48×48 etc.
Unit ( mm ): 1220mm x1220mm, 1220mm x 1830mm, 1220mm x 2440mm, 1220mm x 3048mm, 1220mm x 3658mm, 1524mm x 2440mm, 1524mm x 3048mm, 1830mm x 2440mm .
The above are some commonly used dimensions of aluminum plates, but Huawei Aluminum not only produces and sells conventional aluminum plate dimensions, we also support customizing aluminum plates with special requirements, adding special aluminum plate sizes, special aluminum plate thicknesses, and special aluminum plate alloys that you need Model, special color, special processing technology, please contact us, we will produce according to your needs.
5′ × 10′ aluminum sheet Alloy models have 1100, 3003, 3105, 5005, 5052, 5754, etc
1100 pure aluminum 5′ × 10′ aluminum sheet
The 1100 category in the 1 series belongs to the pure aluminum series with better performance, soft and easy to process and form, and is mostly used for the aluminum plate substrate in the interior and exterior decoration of buildings, but the impact resistance is slightly weaker, and it is easy to be scratched.
3003 alloy aluminum sheet 5′ × 10′
3003 aluminum alloy contains manganese as its main alloying element. 3003 aluminum is an alloy with excellent corrosion resistance and moderate strength. 3003 is the most widely used aluminum alloy. It is basically commercial pure aluminum, with the addition of manganese, the strength is increased by about 100 times.
It cannot be heat treated and can only be strengthened by cold working. 3003 aluminum alloy has good machinability and can be easily welded by conventional welding methods. Commonly used in chemical equipment, piping systems and general sheet metal engineering. 3003 aluminum is commonly used in the manufacture of stamped parts and pressure vessels, architectural hardware, garage doors, awning slats, refrigerator panels, gas pipes, gasoline tanks, heat exchangers, drawn and spinning parts, and storage tanks.
3003 may be slightly discolored when anodized, but it responds well to mechanical and organic finishes. 3003 aluminum tends to be sticky during processing, but with proper settings and maximum speed, it will perform satisfactorily at higher temperatures. Typical end uses include food and chemical processing equipment, electrical components, truck/trailer roofs, heat exchangers, pipe sheathing and lawn furniture components.
5052 alloy 5′ × 10′ aluminum sheet
5052 alloy aluminum sheet and 2.5% magnesium alloy. Tensile strength varies from 31 to 44 KSI. 5052 aluminum sheet has excellent machinability, weldability and corrosion resistance. 5052 aluminum plate is a non-heat-treated aluminum alloy with excellent surface treatment quality.
Although not heat treatable, aluminum sheet 5052 can be strengthened through a work hardening process (5052-H32). 5052 aluminum sheet does not contain copper, so it is less susceptible to salt water corrosion than copper-containing alloys. It has excellent corrosion resistance, especially in marine environments. 052 aluminum can be anodized to improve its corrosion resistance in corrosive environments.
5052 alloy aluminum sheet is commonly used in aircraft fuel tanks, hull structures, storm shutters, refrigerator liners and panels, etc. Complies with AMS QQ-A-250/8 and ASTM B209.
5′ × 10′ 6061 alloy aluminum sheet
6061 alloy aluminum sheet&plate is the most widely used heat treatable aluminum alloy. Although lower in strength than most 2xxx and 7xxx alloys, 6061 aluminum offers a wide range of mechanical properties and corrosion resistance and can be manufactured by many common methods. Combined with higher strength, good corrosion resistance and machinability, 6061 aluminum sheet has become the most widely used sheet grade for all types of manufacturing projects. General purpose 6061 alloy aluminum sheet is heat treatable, resistant to stress cracking, easy to weld and machine, but has limited formability.
In the "O" tempered or annealed condition, 6061 alloy has good formability.
Under the condition of T4, quite serious molding can be carried out;
In the T6 state, performance can be obtained by artificial aging. 6061 t6 aluminum sheet has a high strength-to-weight ratio, making it ideal for any application that requires lightweight components.
6061-T651 aluminum sheet is ideal for most machining techniques and internal and external applications. It is considered the most common heat treatable aluminum alloy with good corrosion resistance. It is a lightweight material with a semi-smooth finish and a matte finish and is typically machined to end-user specifications in a variety of applications such as aircraft and trailers.
6061 alloy aluminum sheet is an ideal material for medical components, structural frames, substrates, gussets, aircraft, marine and automotive parts, etc.
Processing of 5″x10″ aluminum sheet
Common colors of aluminum sheet are gray, white, flash silver, black, silver gray, champagne, etc. The common surface treatment methods of aluminum sheet include fluorocarbon spraying, polyester spraying, powder spraying, wood grain heat transfer, imitation stone Thermal transfer, anodizing, etc. The common modeling methods of aluminum sheet include arc, punching, spherical, curved, carved, hollow, pattern and so on.